EMScannerR: 150 kHz- 8 GHz
The world’s fastest EMC/EMI diagnostic system has been reinvented to assist high-density board designers to visualize the root causes of potential EMC and EMI problems during pre-and post-EMC compliance testing.
EMScannerR enables the PCB and design engineers to diagnose EMC/EMI problems between 150 kHz and 8 GHz. EMScannerR provides 8 levels of resolution (60 microns – 7.5 mm).
Spectral scan, spatial scan, peak-hold, continuous scanning, spectral and spatial comparison, scripting, limit lines, report generation, and notes.
Spatial scan time:
Continuous real-time for the entire scan area (1,218 probes activated) when Level 1 is selected: 5 sec.
Selected area 2.25 cm x 2.25 cm, 9 probes activated.
Level 1: <0.5 sec. | Level 2: 4 sec. | Level 3: 9 sec. | Level 4: 21 sec. | Level 5: 55 sec. | Level 6: 2 min 35 sec. | Level 7: 7 min 23 sec. | Level 8: 24 min 00 sec.
Spectral scan time:
11 seconds for L 10 cm x W 10 cm (L 4” x W 4”, 178 probes activated) from 10 MHz span to 110 MHz and 122 kHz RBW. Scanning area, span, and RBW are user selectable within spectrum analyzer specifications
Supported operating systems:
Picture in JPEG format
Standard Gerber© RS274x format and HPGL form
Broadband frequency coverage:
Base configuration = 150 kHz to 8 GHz
1,218 (42 x 29) H-field probes.
Level 1: 7.50 mm | Level 2: 3.75 mm | Level 3: 1.88 mm | Level 4: 0.94 mm
Level 5: 0.47 mm | level 6: 0.24 mm | Level 7: 0.12 mm | Level 8: 0.06 mm
L 31.6 cm x W 21.8 cm (L 12.44” x W 8.58”)
Frequency accuracy of peaks:
Peak marking accuracy of the spectrum analyzer
Probe to probe uniformity:
Calibrated before shipment. Firmware correction factors adjust for frequency-dependent probe responses with +/- 3 dB accuracy
Measurement plane isolation:
> 20 dB
Maximum radiated power load:
10 W / 40 dBm
Anodized non-conductive metal
Maximum DUT voltage:
Glass Cover: 4kV DC; 2.6kV AC | Metal Case: 260V DC; 200V AC (measured as dielectric withstanding voltage – DWV)
From 15⁰ C to 40⁰ C
Spectrum analyzer: RF SMA to type N coaxial cable | Adapter: Proprietary DB25
Supported Analyzers (If your analyzer is not listed contact Y.I.C. Technologies for driver development)
Keysight: N9000A-CXA, N9000B-CXA, N9010A-EXA, N9010B-EXA, N9020B-MXA, N9020A-MXA, N9038A-MXE, N9912A-FieldFox, N9916A-FieldFox, N9918A-FieldFox, N9952A-FieldFox, E4440A-PSA, N9030A-PXA, N9040B-UXA
Rohde & Schwarz: ZVL, ZVB20, ZNB8, FSW, FSV4, FSV3, FPL
Dimensions of the scanner:
L 34.5 cm x W 43.5 cm x H 11 cm (L 13.58” x W 17.13” x H 4.33”)
12.70 Kg / 28 lb (including cables and the adapter)
To view and/or download EMScanner resources, simply click on the links below:
EMScannerR provides 8 levels of resolution (60 microns – 7.5 mm). Level 1 resolution (7.5 mm) allows the engineers to visualize the hot spots, current loops, or intermittent problems in real time. After locating the unintended radiators, engineers can zoom into the problem by selecting the resolution level based on the density of the board design.
EMScannerR provides unique pre- and post-EMC compliance testing that images emissions. During any new PCB development process, design engineers must find, characterize, and address unintended radiators or RF leakage to pass compliance testing. EMScannerR allows board designers to pre-test and resolves EMC and EMI problems early on, thus avoiding unexpected EMC compliance test results.
High resolution EMC scanner
EMScannerR quickly delivers repeatable and reliable results that pinpoint the cause of a design failure. As a result, the user can personally test the design without having to rely on another department, test engineer, or time-consuming off-site testing. After diagnosing even an intermittent problem, the engineer can implement a design change and retest. The results provide concrete verification of the effectiveness (or not) of the design change.
Y.I.C. Technologies products are compatible with most Spectrum Analyzers.
If you do not have a Spectrum Analyzer and wish to purchase one, please get in touch with us as we have secured relationships with leading test & measurement companies to ensure competitive prices. You are also able to purchase a Spectrum Analyzer directly from Y.I.C. Technologies. Click below to enquire further.
The instrument provides spatial and spectral scans that allow design teams to cut one to two design cycles out of their product development process. It also reduces their EMI testing time by up to two orders of magnitude.
The design team conducted the scans on the EMxpert system in their offices. In a matter of minutes, they obtained the results. Testing the design in a third-party chamber would have been weeks away